Author Guideline

  • IJREI is peer review journal, author should submit only unpublished paper in IJREI, Please make sure that your paper has not published anywhere else. We will not be liable for any duty of copyright disputes caused by the author. Before submission please make sure that your paper is prepared using IJREI paper template. Acceptance or rejection email will be sent to author within 3-5 working days.
  • The manuscript would be considered underall the branches of Engineering &Technology, Managementand Applied Science, but not limited.
Preparation of Manuscript
Margin (inches)
Top 0.5 Bottom 0.5
Left 0.5 Right 0.5
Gutter 0 Gutter position left
Font Size
Title Heading 16, Time New Roman (Bold) Spacing Single line spacing
Main Heading 10, Time New Roman (Bold) Figure Caption 9, Time New Roman (Bold)
Sub Heading 10, Time New Roman (Italic) Table Caption 9, Time New Roman (Bold)
  • Once the paper is accepted, author can pay online any time through online banking, credit card and debit card etc.
  • After successful payment, author should submit the final version of paper, copyright form (filled and signed) and payment proof to editor@ijrei.com..

Research Article
The articles should provide a comprehensive review on scientific topics along with experimental and analytical results.The manuscript should be prepared in English using MS word and it should havethe following headings.

Title Page
This page should contain the title of the paper in bold, title case (16, Time New Roman), name of the author should be in title case (italic, 9, Time New roman) with address. Corresponding author has the responsibility to ensure that all the co-authors are aware and approve the content of the submitted manuscript.

Abstract
An abstract should be summarized in one paragraph with time new roman font size 10, single line spacing, italic, justified and should contain at least 200-250 words. Please do not make references and any type of equation in abstract.

Keywords
Author(s) must give 4-6 appropriate key words after abstract. These keywords should be typed at the end of the abstract.

Introduction
It should be a succinct statement of the background to the work presented, including relevant earlier work, suitably referenced, purpose of the investigation and relating the manuscript to similar previous research.

Materials and Methods
This section must contain all the important materials, equipment's and manufacturer name (if possible) along with location to make it simpler for other researchers to reproduce the result. New methods or substantially modified methods may be described in sufficient detail. The statistical method and the level of significance chosen will be clearly stated.

Captions for figures/tables
Caption of figure and table should beof 9 point Times Roman (Bold) (e.g. Figure 1. Figure name). A caption should be inserted in each figure. The legend should be typed in the manuscript directly beneath the figure. Legends are to be listed in numerical order and shouldlabeled as "Figure 1", "Figure 2" and Table 1, Table 2 etc.

Result and Discussion
In this section elaborate your result and discussion, the font sizefor this section should be 10, times new roman. Do not under line any heading or any content. The result and discussion should be presented briefly. The interpreted results should be clearlyexplained in discussions and should relate them to the existing knowledge in the field as much as possible. Tables, Graphs and figures (Illustrations) should be inserted at the end of the manuscript and should have appropriate numbers and titles with an explanatory heading. Color photographs and illustrations (line drawings, halftones, photos, photomicrographs etc) must be clear, sharp and original. Digital files are recommended for highest quality reproduction and should follow the following guidelines.

  • 300dpi or higher sized to fit journal page
  • JPEG, GIF, TIFF and PDF formats are preferred)
  • Acknowledgement (if any)

Conclusions
A conclusion section must be included and should clearlyindicate the advantages, limitations, and possible applicationsof the paper. Although a conclusion may review the main points of the paper, but do not replicate the abstract as the conclusion. A conclusion must elaborate the importance of the work or suggest applications and extensions.

Acknowledgements

References
References should be written in the following manner
[1] D. Mohanti and P.Hasan, "Analysis of mechanical properties of aluminium alloy, International journal of current research, vol. 2 issue 4 Dec. 2001, 2127-2130
[2] Husain Mehdi, R.S. Mishra, "Analysis of mechanical properties of aluminium alloy, International journal of engineering and technology, vol. 12 issue 4 Dec. 2001, 122-127.

Copyright Form
Submission of the manuscript shows that the manuscript has not been published previouslyand is not considered for publication elsewhere. Content of manuscript should be original. Corresponding author is required to sign a CRF form (Copy Right Form) once the manuscript is accepted which would be sent to thecorresponding author's email. The corresponding author can download the form, sign it and can be send as an attachment file through email or by post/courier..

 

Current News & Updates

Congratulations, IJREI has been indexed with crossref with DOI: http://doi.org/10.36037/IJREI.2021.XXXX

IJREI, invites papers form various Engineering & Technology and Science disciplines for vol-8, issue-4

IJREI received new scientific Journal Impact factor '5.159' for the session of 2021-22

IJREI received new COSMOS Impact factor '2.860' for the session of 2018-19

Congratulations, IJREI journal now indexed in ABCD indexing

Login

 

Indexing and Listing

 
Terms & Conditions Privacy Policy Disclaimer Contact Us